Please use this identifier to cite or link to this item: https://essuir.sumdu.edu.ua/handle/123456789/82298
Or use following links to share this resource in social networks: Recommend this item
Title Contact of working surfaces for spherical washers and recommendations for determining the gap in the joint
Authors Dehtiarov, Ivan Mykhailovych  
Neshta, Anna Oleksandrivna
Samardak, M.P.
Antosz, K.
Avramenko, S.E.
ORCID http://orcid.org/0000-0001-8535-987X
Keywords lapping
turning
tolerance
contact square
manufacturability
Type Article
Date of Issue 2020
URI https://essuir.sumdu.edu.ua/handle/123456789/82298
Publisher Sumy State University
License Creative Commons Attribution - NonCommercial 4.0 International
Citation Dehtiarov I. M., Neshta A. O., Samardak M. P., Antosz K., Avramenko S. E. (2020). Contact of working surfaces for spherical washers and recommendations for determining the gap in the joint. Journal of Engineering Sciences, Vol. 7(2), pp. B1–B7, doi: 10.21272/jes.2020.7(2).b1
Abstract In article analyzes the technical requirements for spherical washers used in threaded connections of pumps, which made it possible to highlight contradictions in paragraphs of the current standards for pump fasteners. They regarding recommendations for manufacturing technology and control of the working surfaces of washers. Publication analysis in the spherical surfaces lapping showed the absence of research in the spherical surfaces contact after lapping and the dependence of contact parameters by the technological parameters for this operation. The presence of a gap in conjunction with spherical washers after the lapping process was proved geometrically. Its location was determined, and a mathematical dependence was obtained to determine the maximum gap value in conjunction. It was found that the gap depends on the design parameters of the washers' conjunction and the abrasive material grain size used for lapping. Recommendations for selecting the abrasive material grain size for the lapping operation for the most common values of the roughness parameters for the working surfaces of spherical washers have been formed. In the article was proposed to introduce into the technical requirements for the spherical washers drawings changes concerning the gap size allowable in the conjunction, and as well as tolerances value changes of the radii of the working surfaces of the washers, thus increasing their manufacturability without conflicting with the requirements of the current standards.
Appears in Collections: Journal of Engineering Sciences / Журнал інженерних наук

Views

Australia Australia
65313062
Austria Austria
1
Bulgaria Bulgaria
1
Canada Canada
1
China China
-1180385528
Czechia Czechia
1
France France
-1180385522
Germany Germany
-280805259
Ireland Ireland
-1105674242
Israel Israel
1
Italy Italy
1
Japan Japan
1
Lithuania Lithuania
1
Moldova Moldova
53575
Netherlands Netherlands
1479608697
Nigeria Nigeria
476111
Norway Norway
1
Russia Russia
1
Singapore Singapore
-280805256
Sweden Sweden
721821999
Turkey Turkey
1476264452
Ukraine Ukraine
-2132039664
United Kingdom United Kingdom
1688058671
United States United States
-1180385524
Unknown Country Unknown Country
-1431388852
Vietnam Vietnam
2748

Downloads

Australia Australia
9635489
China China
1
Croatia Croatia
1
France France
-1180385521
Germany Germany
1476264449
India India
-209505533
Israel Israel
-280805257
Japan Japan
1095527702
Lithuania Lithuania
1
Norway Norway
1
Singapore Singapore
1
South Africa South Africa
1
Switzerland Switzerland
1
Ukraine Ukraine
41947
United Arab Emirates United Arab Emirates
1
United Kingdom United Kingdom
1095527701
United States United States
-1180385526
Unknown Country Unknown Country
1
Vietnam Vietnam
1

Files

File Size Format Downloads
Dehtiarov_jes_2_2020.pdf 963.3 kB Adobe PDF 825915461

Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.