Журнал нано- та електронної фізики (Journal of nano- and electronic physics)
Permanent URI for this collectionhttps://devessuir.sumdu.edu.ua/handle/123456789/197
Browse
3 results
Search Results
Item Structure аnd Physical-Mechanical Properties of nc-TiN Coatings Obtained by Vacuum-Arc Deposition and Deposition with HF Discharge(Sumy State University, 2011) Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr Dmytrovych; Mahmud, A.M.; Karasha, I.T.; Kirik, G.V.; Tkachenko, R.Y.; Shypylenko, A.P.Using the scanning electron microscopy (SEM), X-ray diffraction (XRD) analysis, adhesion strength, friction coefficient, and wear rate of the material we have studied properties of nc-TiN coatings. Depending on the bias potential applied to the substrate and the chamber pressure, the inclusion of HF discharge, it is shown that combination of different parameters recorded during scratching allows to distinguish the threshold values of the critical load which are linked to different types of cohesive and adhesive fracture of coatings in tribological tests. Sizes of nc-TiN nanograins, stoichiometry of coatings, as well as the phase and elemental composition and morphology of the coating surface were determined. When you are citing the document, use the following link http://essuir.sumdu.edu.ua/handle/123456789/35999Item Структура і фізико-механічні властивості нк-TiN покриттів отриманих вакуумно-дуговим осадженням та осадження з ВЧ розрядом(Видавництво СумДУ, 2011) Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr Dmytrovych; Махмуд, А.М.; Караша, І.Т.; Кірік, Г.В.; Ткаченко, Р.Ю.; Шипиленко, Андрій Павлович; Шипиленко, Андрей Павлович; Shypylenko, Andrii PavlovychЗа допомогою растрово-електронної мікроскопії (РЕМ), рентген-структурного аналізу (РСА), адгезійної міцності, коефіцієнта тертя і швидкості зносу матеріалу і були вивчені властивості покриттів нк – TiN. У залежності від потенціалу зміщення, що подається на підкладку і тиску в камері, включення ВЧ розряду, показано, що сукупність різних параметрів реєструються в процесі дряпання, дозволяє розрізняти порогові значення критичного навантаження, прив'язані до різних типів когезійного та адгезійного руйнування покриттів при трибологічних випробуваннях. Були визначені розміри нанозерн нк – TiN стехіометрія покриттів, а також фазовий елементний склади і морфологія поверхні покриттів. При цитуванні документа, використовуйте посилання http://essuir.sumdu.edu.ua/handle/123456789/23734Item physical and mechanical properties of the nanocomposite and combined Ti-N-Si /WC-Co-Cr and Ti-N-Si/(CR3C2)75-(NiCr)25 coatings(Видавництво СумДУ, 2009) Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr Dmytrovych; Каверін, Михайло Валерійович; Каверин, Михаил Валерьевич; Kaverin, Mykhailo Valeriiovych; Il'yashenko, M.V.; Shypylenko, A.P.; Pshyk, A.V.; Beresnev, V.M.; Kirik, G.V.; Erdybayeva, N.K.; Makhmudov, N.A.; Kolisnichenko, O.V.; Tyurin, Yu.N.; Shpak, A.P.Two types of the combined nanocomposite coatings (Ti-N-Si /WC-Co-Cr and Ti-N-Si/ (Cr3C2Ni)75-(NiCr)25) of 160-320 μm thickness were produced using two deposition techniques: the cumulative-detonation and the vacuum-arc deposition with the high-frequency discharge. This gives the possibility (using the combined coatings) to restore the size of worn areas of the tools and demonstrate the high corrosion and wear resistance, to increase the hardness, modulus of elasticity, and plasticity index. Composition of the top coating varied from Ti = 60 at.%, N = 30 at.%, and Si = 10 at.% to Ti = 75 at.%, N = 20 at.%, and Si = 5 at.%. In the first series of coatings the following phases were obtained: (Ti;Si) and TiN in thin top coating and WC and W2C in thick bottom coating. The second series gives (Ti;Si)N and TiN in top coating; Cr3Ni2 and pure Cr in bottom coating; and small amount of Ti19O17 in the transition region between thin and thick coatings. For the first series the grain size achieved 25 nm at the hardness of 38 GPa. For the second series the grain size was 15 nm at the hardness of 42 GРa ± 4 GPa. It is shown that the corrosion resistance in salt solution and acid media increases with the wear decrease as a result of the cylinder friction over the surface of combined coating. При цитуванні документа, використовуйте посилання http://essuir.sumdu.edu.ua/handle/123456789/9351