Видання зареєстровані авторами шляхом самоархівування
Permanent URI for this communityhttps://devessuir.sumdu.edu.ua/handle/123456789/1
Browse
6 results
Search Results
Item Высокодозная ионная имплантация в NiTi для улучшения эффекта памяти формы и псевдопластичности(2013) Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr Dmytrovych; Братушка, Сергій Миколайович; Братушка, Сергей Николаевич; Bratushka, Serhii Mykolaiovych; Левінтант-Заєць, Н.У статті представлені нові результати дослідження впливу високодозової іонної імплантації іонів N+, Mo, W, N та Ni дозою 1018 см – 2 на фізико-механічні властивості сплаву: збільшення зносостійкості сплаву при стиранні поверхневого шару, збільшення нанотвердості, стійкості до корозії, а також зміни морфології поверхні NiTi. Виявлено кореляцію між зміною елементного складу поверхні після ім- плантації і зміною механічних властивостей сплаву. Іншими словами, в результаті високодозової іон- ної імплантації в поверхневому шарі формується наноструктура оксикарбідів та оксинітриду, яка під- вищує зносостійкість, корозійну стійкість і нанотвердість матеріалу. У той же час, об'ємні властивості NiTi (псевдопластічність і ефект пам'яті форми) після імплантації не змінюються, що дозволяє вико- ристовувати іонну імплантацію як ефективний інструмент для поліпшення властивостей матеріалів.Item Shape memory effect in TiNi alloy(Kaunas university of technology, 2012) Братушка, Сергій Миколайович; Братушка, Сергей Николаевич; Bratushka, Serhii MykolaiovychThis paper reports the application of an nitrogen ion implantation for modification of a shape memory alloy. The surface characterization of equiatomic TiNi alloy was performed with the assistance of transmission electron microscopy techniques and the modifications of the phase composition before and after irradiation are studied at the room and martensitic transformation temperatures by X-ray diffraction methods. We investigated the sequence of transformations for the initial and surface-modified materials. Experimental results of near-surface-layers in ion-implanted TNii alloy are discussed in this paper.Item Structure and Properties of Co-Cr Coatings After a Pulsed Jet Treatment(Electrical Review, 2012) Братушка, Сергій Миколайович; Братушка, Сергей Николаевич; Bratushka, Serhii Mykolaiovych; Opielak, M.; Liscak, S.Presents new results on formation and structure of plasma jet, its interaction with working surface regions (in situ). Operation principles of plasma-detonation device (Impulse-6) and application of this technology for Co-Cr coating deposition and tool surface hardening were described. Obtained experimental values of jet parameters (temperature, duration, power), as well as time scanning for current pulses and voltages allowed us to optimize jet parameters for deposition of ceramic, metal-ceramic and alloy coatings to stainless steel substrates. Coating structure was mainly composed of α-fcp- and β-fcc-cobalt. Selected temperature interval for coating formation, according to XRD analysis, allowed us to form intermetalloid compounds of CoxCry-type obalt with chromium.Item Influence of complex treatment on the properties of titanium alloys VT-6(Sumy State University, 2011) Братушка, Сергій Миколайович; Братушка, Сергей Николаевич; Bratushka, Serhii MykolaiovychThe paper presents new results on investigation of structure and physical-mechanical properties of near surface layers of titanium alloys VT-6 after (W+, Mo+) ion implantation and subsequent thermal annealing under 550oC during 2 hours. Using back scattering (RBS) of helium ions and protons, scanning electron microscopy (SEM) with microanalysis (EDS), (WDS), proton (ion) induced X-ray emission (PIXE), X-ray phase analysis (ERD) with a sliding beam geometry (0.5oC), Mössbauer spectroscopy (MS), measurements of nanohardness and elastic modulus, friction wear (cylinder-plate), measurements of corrosion resistance in a salt solution, we investigates VT-6 samples, and determined their fatigue resistance under cyclic loads. Two times increase of the hardness, decrease of wear and increased fatigue resistance was found, which was related to the formation of small dispersion (nanodimension) nitride, carbonitride, and intermetalloid phases.Item Structures and properties of Ti alloys after double implantation(Elsevier, 2009) Братушка, Сергій Миколайович; Братушка, Сергей Николаевич; Bratushka, Serhii Mykolaiovych; Uglov, V.V.; Rusakov, V.S.; Beresnev, V.M.; Malikov, L.V.; Levintant, N.; Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr Dmytrovych; Erdybaeva, N.K.; Anischik, V.M.; Levintant, N.The paper presents new results on investigation of structure and physical-mechanical properties of near surface layers of titanium alloys after (W+, Mo+) ion implantation and subsequent thermal annealing under 550 C for 2 h. Using back scattering (RBS) of helium ions and protons, scanning electron microscopy (SEM) with microanalysis (EDS), (WDS), proton (ion) induced X-ray emission (PIXE), X-ray phase analysis (XRD) with a grazing incidence geometry (0.5 angle), measurements of nanohardness and elastic modulus, friction wear (cylinder-plate), measurements of corrosion resistance in a salt solution, we investigated the VT-6 samples, and determined their fatigue resistance under cyclic loads. Double increase of hardness, decrease of wear and increased fatigue resistance were found, which was related to the formation of small dispersion (nanodimension) nitride, carbonitride, and intermetalloid phases.Item Structure and Composition of Near-Surface Layers in the Ion-Implanted NiTi Alloy(Publishing House of the IOA SB RAS, 2010) Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr Dmytrovych; Братушка, Сергій Миколайович; Братушка, Сергей Николаевич; Bratushka, Serhii Mykolaiovych; Levintant, N.Поверхностный слой сплава TiNi, обладающего эффектом памяти формы в мартенситном состоянии, изменен высокой дозой имплантированныъ ионов N + ионов (дозы имплантации варьируется от 1017 до 1018 ion/cm2). TiNi образцов, имплантированных N +, Ni +-N +, и Мо +-W + при дозе 10l7-1018 см-2 и изучены обратным рассеяния Резерфорда. сканирующей электронной микроскопией, энергетической дисперсионной спектроскопией, рентгеновской дифракции (скользящей геометрией), и путем измерения нанотвердости и модуль упругости. Ni + концентрации обнаружен пик между двумя максимумами в глубину профиля концентрации ионов N +. Рентгеновской дифракции образцов TiNi имплантированных Ni + и N + ионов показывает формирование TiNi (B2), олово и Ni3N фаз. В исходном состоянии, модуль упругости образцов E = 56 ГПа при твердости Н = 2,13 ± 03 ГПа (на глубине 150 нм). После двойной имплантации Ni +-N + и Мо +-W + ионов, твердость образцов TiNi является 2,78 ± 0,95 ГПа на глубине 150 нм и 495 ± 2,25 ГПа на глубине 50 нм, модуль упругости 59 ГПа. Отжиг образцов при температуре 550 ° С приводит к увеличению твердости 4,44 ± 1,45 ГПа и резкое увеличение модуля упругости до 236 ± 39 ГПа. Корреляции между элементным составом, микроструктурой и механическими свойствами поверхностного слоя в TiNi не найдено.