Факультет технічних систем і енергоефективних технологій (ТеСЕТ)
Permanent URI for this communityhttps://devessuir.sumdu.edu.ua/handle/123456789/25
Browse
Search Results
Item Design of a shelf pneumatic classifier for separating a polydisperse mixture of granulated superphosphate(РС ТЕСHNOLOGY СЕNTЕR, 2022) Юхименко, Микола Петрович; Yukhymenko, Mykola Petrovych; Острога, Руслан Олексійович; Ostroha, Ruslan Oleksiiovych; Bocko, J.The object of this study is a polydisperse mixture of granular superphosphate. It is emphasized that existing technologies of granulation and processing of granules lead to the formation of dusty fractions of small particles. The content of small fractions in the finished product should be minimal and, in connection with this problem, the task is to remove small particles from the mixture. The purpose of the current experimental study is to classify a polydisperse mixture of granular superphosphate in a pneumatic classifier. The device includes an inclined perforated shelf with an unloading space between its end and the wall of the apparatus. It has been experimentally revealed that the maximum efficiency of extraction into the entrainment of small particles is achieved with a width of the discharge space equal to 0.5 of the length of the cross-sectional side of the apparatus; the degree of perforation of the shelf is 5 %; the angle of inclination of the shelf is 25–30°; the speed of the gas flow in the free section of the apparatus is 3.7 m/s. It is shown that the degree of extraction into the entrainment of a small fraction less than 1 mm in size reaches 70–75 %, the content of the small fraction in the carry-over is 96–98 %, and the large fraction is less than 5 %. By processing experimental data, an empirical equation was built that makes it possible to determine the concentration of particles in the gas stream for individual fractions of the material. It is shown that due to the implementation of an active aerodynamic weighing mode, the shelf pneumatic classifier works at specific loads for air flow rate less than the typical designs of fluidized bed separators. It is noted that the effective operation of the shelf pneumatic classifier in the production of granular mineral fertilizers is ensured at a productivity of no more than 10–12 t/h. With greater productivity, there is a need to install several devices in the technological line.Item Experimental Studies and Condition Monitoring of Auxiliary Processes in the Production of Al2O3 by Sol–Gel Technology(MDPI, 2022) Склабінський, Всеволод Іванович; Склабинский, Всеволод Иванович; Sklabinskyi, Vsevolod Ivanovych; Ляпощенко, Олександр Олександрович; Ляпощенко, Александр Александрович; Liaposhchenko, Oleksandr Oleksandrovych; Piteľ, J.; Павленко, Іван Володимирович; Павленко, Иван Владимирович; Pavlenko, Ivan Volodymyrovych; Скиданенко, Максим Сергійович; Скиданенко, Максим Сергеевич; Skydanenko, Maksym Serhiiovych; Острога, Руслан Олексійович; Острога, Руслан Алексеевич; Ostroha, Ruslan Oleksiiovych; Юхименко, Микола Петрович; Юхименко, Николай Петрович; Yukhymenko, Mykola Petrovych; Simeiko, K.; Demianenko, M.; Volf, M.; Starynskyi, O.; Юрченко, Олександр Юрійович; Юрченко, Александр Юрьевич; Yurchenko, Oleksandr Yuriiovych; Мандрика, О.Powders and granules of heavy metal oxides produced through condition monitoring are in high demand as intermediate products for obtaining fine-grained ceramics for a wide range of applications, i.e., nuclear fuel and fuel elements for nuclear power plants. Sol–gel technology to produce nuclear fuel (UO2), as well as catalysts (ThO2) for organic synthesis in the form of granules from pressed microspheres, is a promising method to obtain powders and granules of heavy metal oxides (fine-graded ceramics). Al2O3 was selected as the model analog at the stages of obtaining a solution of heavy metal and sol, the formation and gelation of droplets, and the preparation of gel spheres and their further washing and drying, as well as recovery and firing of particles. In the study, the main parameters were substantiated, e.g., the diameter and angle of inclination of the axis for the holes in the perforated shell, the multiplicity of sol circulation before the holes, the coefficients of liquid (sol) flow rate, the oscillation frequency of the disperser, and the concentration of surfactant and acid in sol. All of these parameters affect the characteristics of the granules that are obtained by sol–gel technology. Moreover, recommendations to increase productivity and the energy efficiency of production were also given. In particular, it was found that oscillation frequency in a range of 70–80 Hz leads to a granulometric composition of the obtained granules of 2.0–2.2 mm. A hole of 0.85 mm and a frequency of 100 Hz slightly change this range to 1.2–2.0 mm, while maintaining monodispersity.