Факультет електроніки та інформаційних технологій (ЕлІТ)
Permanent URI for this communityhttps://devessuir.sumdu.edu.ua/handle/123456789/20
Browse
3 results
Search Results
Item Effect of the PEN/C surface layer modification on the microstructure, mechanical and tribological properties of the 30CrMnSiA mild-carbon steel(Elsevier, 2020) Zhurerova, L.G.; Rakhadilov, B.K.; Popova, N.A.; Kylyshkanov, M.K.; Буранич, Володимир Володимирович; Буранич, Владимир Владимирович; Buranych, Volodymyr Volodymyrovych; Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr DmytrovychAs a result of plasma-electrolytic nitrocarburizing 30CrMnSiA carbon steel (ferrite-perlite grade), there was a change in the elemental and phase composition, as well as the surface layer microstructure (40 ÷ 45 microns thick from the surface). A formation of Me23(CN)6 carbonitrides, FeN nitrides, Fe3C - (Fe, Cr)3C carbides and an increase in dislocation density within –phase (tempered martensite crystallites), high-temperature lamellar martensite were observed. As a result of PEN / C exposure for 7min. At 750 ◦C there is a reduction of friction coefficient and wear rate, what is connected with finely dispersed secondary phases FeN, (Fe, Cr)3C, Me23(C, N)6 formation. Thus, there is an 2,5 ÷ 3,3 times increase in hardness of 30CrMnSiA carbon steel samples.Item Electrolytic plasma processing for plating coatings and treating metals and alloys(Springer, 2014) Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr Dmytrovych; Каверіна, Аліса Шер Ахмад; Каверина, Алиса Шер Ахмад; Kaverina, Alisa Sher Akhmad; Kylyshkanov, M.K.A review of the methods of electrochemical treatment classified as plasma electrolysis is given. Special attention is paid to the physicochemical processes that proceed in electrolytes and the techniques of surface modification and application of protective coatings. The results of investigation of such coatings and surfaces upon electrolytic plasma processing illustrate the efficiency and effectiveness of the method. Being an efficient technique of the surface treatment, which involves both the surface cleaning and plating the coating, the plasma electrolytic method is being rapidly developed and adapted for commercial use at present.Item Исследование влияния параметров осаждения на структуру и физико-химические свойства защитных покрытий из Al2O3(Издательством "Наука", 2013) Погребняк, Олександр Дмитрович; Погребняк, Александр Дмитриевич; Pohrebniak, Oleksandr Dmytrovych; Комаров, Ф.Ф.; Комаров, Ф.Ф.; Komarov, F.F.; Каверіна, Аліса Шер Ахмад; Каверина, Алиса Шер Ахмад; Kaverina, Alisa Sher Akhmad; Соболь, О.В.; Соболь, О.В.; Sobol, O.V.; Тюрин, Ю.М.; Тюрин, Ю.Н.; Tyurin, Yu.M.; Купчишин, А.І.; Купчишин, А.И.; Kupchishin, A.I.; Килишканов, М.К.; Кылышканов, М.К.; Kylyshkanov, M.K.Три серии образцов покрытий Al2O3 были получены методом микродугового оксидирования при различных условиях осаждения. Они были исследованы с помощью SEM-микроскопии с EDXS, RBS и рентгенофазового анализа XRD. Дефекты и поры в покрытии были исследованы методом позитронной аннигиляционной спектроскопии (PALS) при комнатной температуре, без вакуума. В процессе исследования не обнаружено образование нанометровых пор. Показано, что, меняя условия электролитно-плазменной обработки, можно изменять концентрацию и соотношение разного типа вакансионных дефектов в покрытии из Al2O3. При цитировании документа, используйте ссылку http://essuir.sumdu.edu.ua/handle/123456789/33926