Journal of Engineering Sciences / Журнал інженерних наук
Permanent URI for this collectionhttps://devessuir.sumdu.edu.ua/handle/123456789/34326
Browse
5 results
Search Results
Item Standardizing life cycle organization: A synergetic quality management approach(Sumy State University, 2023) Prokopovych, I.V.; Kokhanov, A.B.; Khamitov, V.M.; Tikhenko, V.M.; Dašić, P.Standardization is essential for innovation (on the impacts on design, manufacturing, and operation processes) and its dissemination, both within a country and internationally. A phenomenological information model has been developed for the system of standards, which will be used as an information base for integrated quality management systems, environmental safety, and energy saving depending on the type of products, requirements of technical regulations, and conformity assessment procedures. Phase portraits of the life cycle system of complex products were constructed, and a general expression for the Lyapunov exponents characterizing the overall behavior of the dynamic system in phase space was obtained. The presence of particular areas to which, regardless of the initial conditions, all phase trajectories rapidly evolve has been established. The critical conditions for the control parameters were found. A diagram was constructed that determines the stability of the system states of the life cycle of complex products. It was found that the processes of the life cycle of complex products are carried out in two stages: in the first, there is a rapid evolution of components and parameters of technical and software tools, as well as energetic elements of functional subsystems, which is reflected in a specific attractive section of phase portraits, in the second, further slow development along it.Item The efficiency of collaborative assembling cells(Sumy State University, 2022) Андрусишин, Владислав Костянтинович; Андрусишин, Владислав Костантинович; Andrusyshyn, Vladyslav Kostiantynovych; Luscinski, S.; Іванов, Віталій Олександрович; Иванов, Виталий Александрович; Ivanov, Vitalii Oleksandrovych; Павленко, Іван Володимирович; Павленко, Иван Владимирович; Pavlenko, Ivan VolodymyrovychTo produce competitive products, it is necessary to consider their permanent modernization and adaptation to the emerging needs of a consumer. This feature of up-to-date production inevitably leads to design complexities. As a result, the complexity of a technological assembly process increases, which is a new challenge for enterprises. Simultaneously, in most cases, assembly operations are performed manually due to the complexity or impossibility of automating the assembling process for an extensive range of products. This fact is due to the insufficient flexibility of automation systems. Remarkably, this approach has significant drawbacks, i.e., low productivity and risk of chronic diseases. To solve this problem, the use of collaborative systems was proposed. Such systems have the advantages of both humans and automation tools. As a result, industrial robots can be applied as automation tools. However, when using industrial robots next to workers, the safety requirements are significantly increased since the infliction of industrial injuries is unacceptable. After considering all the above, the article deals with a new scientific and methodological approach to designing security systems of collaborative production cells and their design and effectiveness verification.Item Analysis of nanoparticles characteristics with TOPSIS for their manufacture optimization(Sumy State University, 2022) Javanbakht, T.The present study focuses on the comparative analysis of superparamagnetic iron oxide nanoparticles (SPIONs) characteristics with the TOPSIS method. The prediction of the characteristics of SPIONs is required for better manufacturing of these nanoparticles. Although the characteristics of these nanoparticles have been investigated, no research has been done on their comparison in order to determine which one of their surface functionalities would be more appropriate for their diverse applications. The objective of this study was to analyze the characteristics of SPIONs without or with surface charge with a prediction model and TOPSIS in order to determine the best nanoparticles. Moreover, the effect of inappropriate consideration of their cost criterion on their ranks was explored with the modified TOPSIS. This analysis showed that the characteristics of SPIONs such as antibiofilm activity, hemocompatibility, activity with hydrogen peroxide, rheological properties, and the labour of their chemical synthesis could affect their ranking. Neutral SPIONs, negatively charged SPIONs, and positively charged SPIONs were ranked as the first, second, and third candidates, respectively. However, the improvement of the activity of positively charged SPIONs with hydrogen peroxide showed an increase to 0.3 instead of 0.2, which resulted in a better rank of these nanoparticles in comparison with that of the same nanoparticles in the first analysis series. One of the advantages of this study was to determine the impact of the characteristics of SPIONs on their ranking for their manufacturing. The other advantage was getting the information for further comparative study of these nanoparticles with the others. The results of this work can be used in manufacturing engineering and materials science.Item Digital model and assembling of a lathe(Sumy State University, 2022) Besedin, M.; Popowska, M.; Іванов, Віталій Олександрович; Иванов, Виталий Александрович; Ivanov, Vitalii Oleksandrovych; Trojanowska, J.The article aims at developing a digital model of a lathe and the related technology for its assembling. The study is based on analyzing the service purpose and technological capabilities of modern modular machine tools, justification and development of the machine tool design according to the specified production conditions, and development of a technological process for assembling the proposed modular machine tool. The geometric modeling techniques and the design documentation were implemented to justify the rational choice of design parameters of the machine tool design and its spatial model. The proposed approach also considers structural elements and the relationships between them. As a result, a conceptual approach was proposed to design technological processes of lathe assembly with a wide range of technological capabilities. It allows implementation of the up-to-date strategy from idea to finished product at industrial enterprises. The practical significance of the obtained results for the machine-building industry is in the proposed practical recommendations for developing the technological process for assembling lathes.Item Investigation on the rheological properties of polydimethylsiloxane(Sumy State University, 2022) Javanbakht, T.This paper focuses on studying the rheological properties of polydimethylsiloxane (PDMS). This polymer has been used to fabricate membranes and filters in engineering. The analysis of the rheological properties of this polymer is required for a further investigation of its mechanical behavior. In this study, the rheological behavior of PDMS is reported at different temperatures. This polymer showed steady shear viscosity during a short duration. However, this behavior changed with time and increased more with increasing temperature. The impact of the temperature increase was also observed when the shear viscosity of PDMS increased with shear strain. The increase of torque with shear strain and time was observed at different temperatures. Shear stress increased linearly with the shear rate at 20 °C and 40 °C. As expected, the deformation of the polymer required less shear stress with the increase of temperature. However, the change of shear stress with the shear rate at 60 °C was not linear, and the slope of the curve increased more at high shear rates. The results of this investigation can provide the required information for a better fabrication of membranes and filters with this polymer.