Journal of Engineering Sciences / Журнал інженерних наук
Permanent URI for this collectionhttps://devessuir.sumdu.edu.ua/handle/123456789/34326
Browse
5 results
Search Results
Item Mathematical model of the tensioning in the collet clamping mechanism with the rotary movable input link on spindle units(Sumy State University, 2021) Prydalnyi, B.I.; Sulym, H.T.Increasing machining productivity causes the cutting forces acting on tools or workpieces to grow and requires extra clamping forces for their fixation reliably. In the research, a mathematical model of the operation of the clamping mechanism for fixating cylindrical objects on the spindle of machine tools at the stage of tension is presented. The presented design of the mechanism contains screw gear and provides self-braking. Based on the calculation model, mathematical dependencies are developed to describe the relationship among the movements of the parts of the mechanism when clamping forces are growing. The presented analytical dependencies allow considering the stage of growing clamping forces separately when the conservative type of forces are prevailing in the mechanism's operation. That stage of work when both types of forces of dissipative and potential characters exist is considered. The developed dependencies describe the position of parts of the clamping mechanism depending on the generalized coordinate. The angle of rotation of the input rotating link is used as the generalized coordinate. This fact allows calculating the position of the elements of the clamping mechanism of this type depending on time. Results of the research enhance understanding the pattern of the change in the interaction of the elements and forces that act in the mechanism during the final stage of clamping. The obtained mathematical dependencies are a precondition for the development of design methodology for mechanisms of this type.Item Особенности обработки различных типов внутренних резьб мерным инструментом(Сумский государственный университет, 2016) Нешта, Анна Олександрівна; Нешта, Анна Александровна; Neshta, Anna Oleksandrivna; Криворучко, Дмитро Володимирович; Криворучко, Дмитрий Владимирович; Kryvoruchko, Dmytro VolodymyrovychНа основании анализа последних исследований были выявлены недостатки существующих методов формообразования внутренних резьб, реализуемых различными способами обработки. Способ обработки круглой резьбы мерным инструментом показал высокую производительность по сравнению с известными способами. Дальнейшие исследования его возможного применения при обработке других типов резьб являются актуальной задачей, для реализации которой необходимо определить диаметр инструмента и параметры траектории его движения. Графическим способом определены реальные профили поперечных сечений. Аналитическим способом получены математические зависимости, связывающие шаг и форму профиля резьб с размерами инструмента и параметрами настройки оборудования. Определены номинальные диаметры мерного инструмента и радиусы спиральной траектории его движения для метрической, дюймовой и круглой резьб. Получены коэффициенты регрессии, характеризующие степень влияния внутреннего диаметра и шаг резьбы на диаметр мерной фрезы.Item Measuring of roundness after turning of composite material with natural fibers(Sumy State University, 2016) Mital, D.; Zajac, J.; Botko, F.; Hatala, M.; Mitalova, Z.; Radchenko, S.; Іванов, Віталій Олександрович; Иванов, Виталий Александрович; Ivanov, Vitalii OleksandrovychThe article is based on practical requirements from the reason of unequally removed material during the turning of the wood plastic composite (WPC). This results in geometrical deviations of the WPC bar diameter. WPC represents a relatively new group of materials that has been at the market for almost 30 years. In 1983 Lear Corporation in Wisconsine, USA made for the first time the interior panels of cars from composite materials – PP matrix with organic filler – 50 % wood flour. WPCs displace traditional materials such as wood, steel and cement materials in the marina industry. Designers are not limited technology of production from construction aspect, because different shapes and profiles can be produced by injection (resp. process of extrusion), but in the process of machining were monitored problems with tolerances. Mixed colors can be achieved by using of different pigments and one feels that this is real wood. Technologists begin to use convention technologies – drilling, milling and turning, as tendency of application of WPC increased. Knowledges about machining of WPC are not elaborate as deep as machining of metals or plastics. And this is a reason for orientation in this direction too. Commercial wood plastic composite MEGAWOOD (70 % wood flour, 30 % HDPE) was a sample material in current investigation of roundness after turning of WPC. HSS EN ISO HS6-5-2 cutting tool was used. The geometry of the cutting tool was γ0 = 20°, α0 = 8°, κr = 45°, rε = 0,5 mm, εr = 90°. Cutting conditions during turning were as follows: cutting speed n = 900 m/min (constant), feed f = 0,1 to 0,61 mm), depth of cut ap = 0,5 mm for turning of final diameter d = 36 mm. It was dry turning. Roundness/ cylindricity measuring system RA – 120 was used for measuring of roundness deviation. It was found that the roundness deviation increases with feed increasing. Popped heat was not used during the turning to final diameter – 36 mm. Using of popped heat results in decreasing of roundness deviation. Waviness was not possible to measure within the range of ±1 000 μm on the sample No. 4 (f = 0,41 mm) and sample No. 5 (f = 0,6 mm). Tip of the measuring systems could not filtrate parameter of roughness (surface after turning – low value of tool nose radius rε = 0,5 mm and high feed caused distinctive toolmark). Inaccuracy of macrogeometry (including roundness) could have caused state of machine, tool and fixture too.Item Интегрированная технология изготовления зубчатых колес из волокнистых полимерных композиционных материалов(Сумский государственный университет, 2014) Осадчий, Ігор Олегович; Осадчий, Игорь Олегович; Osadchyi, Ihor Olehovych; Криворучко, Дмитро Володимирович; Криворучко, Дмитрий Владимирович; Kryvoruchko, Dmytro Volodymyrovych; Родин, И.С.Зубчасті передачі є невід'ємною частиною багатьох механізмів і машин. Поява нових композиційних матеріалів дає поштовх збільшенню навантажувальної здатності зубчастих передач і зниженню їх маси. Метою цієї роботи є розробка інтегрованої технології виготовлення зубчастих коліс (ЗК) із застосуванням волокнистих полімерних композиційних матеріалів (ВПКМ). Аналіз літератури виявив тільки окремі розрізнені дослідження в цій області, які присвячені розробці способів підвищення працездатності ЗК. Технологічна спадковість при виготовленні зубчастих коліс з ВПКМ значно сильніше і тому вплив етапів технологічного процесу має бути обов'язково прийнято до уваги при його проектуванні. Це дозволить при оптимізації схеми укладки армуючих волокон врахувати не тільки необхідність забезпечення їх орієнтації в напрямку найбільших навантажень, але і мінімізувати їх пошкодження при подальшій обробці різанням у разі отримання коліс високого ступеня точності. У роботі показано, що навантажувальна здатність ЗК, виконаних з вуглепластика, знаходиться на рівні навантажувальної здатності ЗК з інших неметалічних матеріалів, проте тільки у вуглепластикових ЗК є великий резерв підвищення навантажувальної здатності за рахунок оптимізації схеми уклади волокон і технології їх виготовлення, який ще не вичерпаний.Item Експериментальне дослідження температури різання при точінні порошкових спечених матеріалів(Сумський державний університет, 2014) Ткачук, І.Є.В якості матеріалів для вузлів тертя в сучасному машинобудуванні широке застосування находять порошкові антифрикційні матеріали. Головною особливістю спечених порошкових матеріалів є наявність пористої структури, що забезпечує самозмащування при роботі вузлів тертя. В процесі різання спечених матеріалів важливу роль відіграють теплові явища. Саме вони визначають температуру в зоні різання, що впливає на характер створення мікроструктуру поверхневого шару. В цій роботі наведено методику проведення експериментальних досліджень температури різання при механічній обробці пористих спечених матеріалів. На підставі отриманих результатів розроблена математична модель для визначення температури різання з врахуванням факторів що на неї впливають: режимів різання та пористості оброблюваного матеріалу.