Факультет технічних систем і енергоефективних технологій (ТеСЕТ)
Permanent URI for this communityhttps://devessuir.sumdu.edu.ua/handle/123456789/25
Browse
11 results
Search Results
Item Чисельні дослідження сопел із різними геометричними параметрами(Сумський державний університет, 2025) Салімов, Є.О.; Садовський, І.Д.; Бага, Вадим Миколайович; Baha, Vadym MykolaiovychСоплові апарати є ключовими елементами в конструкції турбомашин, які виконують функцію спрямування потоку робочого тіла та керування його швидкістю й напрямком руху. Вони відіграють вирішальну роль у підвищенні ефективності роботи газових і парових турбін, компресорів, реактивних двигунів та інших енергетичних установок.Item Моделювання енергосистем в Україні(Сумський державний університет, 2025) Лавриненко, А.О.; Бага, Тетяна Сергіївна; Baha, Tetiana Serhiivna; Бага, Вадим Миколайович; Baha, Vadym MykolaiovychМоделювання енергосистем є критично важливим для України, оскільки країна переживає масштабні трансформації у сфері енергетики, зумовлені геополітичними викликами, необхідністю декарбонізації та інтеграцією до європейської енергосистеми.Item Influence of the degree of off-design of the traction nozzle of a jet reaction turbine on its efficiency(IOP Publishing Ltd, 2021) Ванєєв, Сергій Михайлович; Vanieiev, Serhii Mykhailovych; Родимченко, Тетяна Сергіївна; Rodymchenko, Tetiana Serhiivna; Мелейчук, Станіслав Станіславович; Meleichuk, Stanislav Stanislavovych; Бага, Вадим Миколайович; Baha, Vadym Mykolaiovych; Bolotnikova, О.At the present stage of social development, the need for rational use of energy resources of the planet is particularly acute. Most countries have already faced the problem of the energy crisis. An appropriate way to solve this problem is the utilization of secondary energy resources. With the help of turbine generators, it is possible to reduce the pressure and utilize the potential energy of excess pressure of gas or vapours to produce electricity. Such units can be created based on a jet reaction turbine. The study aims to assess the impact of the degree of off-design of the traction nozzle on the efficiency of the jet reactive turbine. The analysis of the factors influencing the efficiency of the jet reaction turbine is carried out in the work. The obtained efficiency rate for the jet reactive turbine depending on the given dimensionless velocity of λout.t at the inlet pressure of the inlet nozzle of 2, 4, 6 and 10 MPa in the design mode (at the degree of off-design of S = 1) and in the off-design modes of operation ( S> 1). Graphical dependencies of the jet reaction turbine efficiency rate on the given circular velocity of the impeller are constructed (U ̅ = 0… 0.7). The research shows that with increasing pressure at the inlet to the inlet nozzle, the efficiency rate of the turbine increases, and the optimum of the efficiency rate is shifted towards the increase of the given circular velocity of the impeller, both in the design and off-design operating modes. It is found that the greatest value of the efficiency rate is acquired at the design mode of operation of the traction nozzle, i.e. at S = 1.Item Numerical Simulation of Gas Flow Passing through Slots of Various Shapes in Labyrinth Seals(MDPI, 2022) Бага, Вадим Миколайович; Бага, Вадим Николаевич; Baha, Vadym Mykolaiovych; Lishchenko, N.; Ванєєв, Сергій Михайлович; Ванеев, Сергей Михайлович; Vanieiev, Serhii Mykhailovych; Mizakova, J.; Родимченко, Тетяна Сергіївна; Родимченко, Татьяна Сергеевна; Rodymchenko, Tetiana Serhiivna; Pitel, J.Labyrinth seals are widely used in centrifugal compressors, turbines, and many other pneumatic systems due to their simplicity of design, reliability, and low cost. The calculation scheme for the movement of the working medium in a labyrinth seal is constructed by analogy with the movement of the working medium through holes with a sharp edge. Annular and flat slots, holes, and such a factor as the shaft rotation with a calculated sector of 3 degrees were studied. The purpose of the study is to determine the flow coefficient when the working medium flows through slots of various shapes. To achieve this purpose, modeling of the working medium flow in the FlowVision software was performed. The mass flow and flow coefficients are determined for the studied slot shapes. The convergence of the calculation results was determined by comparing the values of the mass flow rate at the inlet and outlet of the slot. Differences in visualizations of the flow for the studied variants of slots were established. The resulting difference should be taken into account in practical calculations of the working medium mass flow through the slot using a conditional flow rate factor which is determined by the slot design.Item Analysis of the possibility of using R718 for a heat pump of a heating system based on a liquid-vapor ejector(Technology Center, 2020) Шарапов, Сергій Олегович; Шарапов, Сергей Олегович; Sharapov, Serhii Olehovych; Гусєв, Данило Максимович; Гусев, Даниил Максимович; Husiev, Danylo Maksymovych; Панченко, Віталій Олександрович; Панченко, Виталий Александрович; Panchenko, Vitalii Oleksandrovych; Козін, Віктор Миколайович; Козин, Виктор Николаевич; Kozin, Viktor Mykolaiovych; Бага, Вадим Миколайович; Бага, Вадим Николаевич; Baha, Vadym MykolaiovychThe study explores the possibility of using water (R718) as a refrigerant for a heat pump installation of a heating system. This unit is a vapor compression heat pump with a regenerative heat exchanger in which the vacuum unit based on a liquid-vapor ejector is used instead of a scroll refrigeration compressor. The work-ing process of such an apparatus is based on implement-ing a fundamentally new cycle that does not require the supply of working steam from the outside. Instead, steam is generated inside the vacuum unit. The arti-cle describes the proposed installation and its differ-ences from the traditional one, both in terms of circuit solutions and in terms of the operating cycle. A ther-modynamic calculation was performed for the proposed installation with R718 as the working medium and the traditional heat pump systems operating on refriger-ants R142b, R254fa, and R410a. As a result of the cal-culation, the parameters of all the devices included in these schemes were obtained, and the conversion factors of the cycles were determined. To assess the feasibili-ty of using R718 as a working substance and replacing the scroll refrigeration compressor with a liquid-vapor ejector, an exergy analysis was performed. This made it possible to fairly accurately determine the effective-ness of each circuit, since it implemented the possibility of comparing systems using several types of energy (for example, electrical and thermal). As a result, the val-ues of exergetic efficiency of traditional and proposed schemes were obtained. The final stage of the study was the performance of a thermoeconomic analysis. The esti-mated cost was determined for a unit of heat quantity per ton of the product and per unit of the heated area obtained in a unit with the working substance R718 and traditional installations with the working substances R142b, R254fa, and R410a.Item Підвищення ефективності лабіринтних ущільнень(Сумський державний університет, 2017) Бага, Вадим Миколайович; Бага, Вадим Николаевич; Baha, Vadym Mykolaiovych; Подоляка, О.І.В данній роботі проводилися чисельні дослідження із застосуванням гідродинамічного програмного комплексу FlowVision для розрахунку течії у вузьких осьових зазорах лабіринтного ущільнення, за результатами яких одержані нові дані по детальному дослідженню ущільнення з гладким валом.Item Дослідження впливу масштабного фактору на характериститки лабіринтних ущільнень(Сумський державний університет, 2017) Бага, Вадим Миколайович; Бага, Вадим Николаевич; Baha, Vadym Mykolaiovych; Мартиш, Д.С.Масштабний фактор в даній роботі досліджувався на лабіринтному ущільненні покривного диска відцентрового компресора шляхом зменшення і збільшення його геометричних розмірів на різних режимах роботи.Item Численное и физическое моделирование узла уплотнения центробежной компрессорной ступени(Сумский государственный университет, 2014) Бага, Вадим Миколайович; Бага, Вадим Николаевич; Baha, Vadym MykolaiovychНесмотря на простоту конструкции и изученность характеристик лабиринтных уплотнений продолжается поиск оптимальных решений. Лабиринтные уплотнения бывают концевыми и промежуточными. Расход рабочей среды через уплотнение существенно снижает к.п.д. машин тем больше, чем больше относительная величина протечки. Лабиринтные уплотнения не являются полностью герметичными, они должны ограничивать перетоки среды между полостями с различным давлением.Item Влияние физических свойств газов на характеристики лабиринтного уплотнения(Сумский государственный университет, 2015) Бондаренко, Герман Андрійович; Бондаренко, Герман Андреевич; Bondarenko, Herman Andriiovych; Бага, Вадим Миколайович; Бага, Вадим Николаевич; Baha, Vadym MykolaiovychНесмотря на наличие экспериментальных и теоретических исследований течения газа в лабиринтных уплотнениях, строгая методика расчета параметров потока в зазоре отсутствует.Item Численное моделирование течения в лабиринтных уплотнениях(Сумский государственный университет, 2013) Бондаренко, Герман Андрійович; Бондаренко, Герман Андреевич; Bondarenko, Herman Andriiovych; Бага, Вадим Миколайович; Бага, Вадим Николаевич; Baha, Vadym MykolaiovychДля герметизации газовых сред в центробежном компрессоре, паровых и газовых турбинах используют различные конструкции лабиринтных уплотнений с минимальными поверхностями контакта. Лабиринтные уплотнения не являются полностью герметичными, они должны ограничивать перетоки среды между полостями с различным давлением. Лабиринтные уплотнения бывают концевыми и промежуточными. При цитировании документа, используйте ссылку http://essuir.sumdu.edu.ua/handle/123456789/31320