Please use this identifier to cite or link to this item: http://essuir.sumdu.edu.ua/handle/123456789/74402
Or use following links to share this resource in social networks: Recommend this item
Title Microstructural Features and Tribological Behaviour of Low-Alloyed Steel Modified by High-Energy Plasma Pulse
Other Titles Особливості мікроструктури та трибологічні властивості низьколегованої сталі, модифікованої високоенергетичним плазмовим імпульсом
Authors Chabak, Yu.G.
ORCID
Keywords імпульсно-плазмова обробка
модифікування
мікроструктура
зносостійкість
коефіцієнт тертя
pulsed-plasma treatment
modification
microstructure
wear resistance
friction coefficient
Type Article
Date of Issue 2019
URI http://essuir.sumdu.edu.ua/handle/123456789/74402
Publisher Sumy State University
License
Citation Chabak, Yu.G. Microstructural Features and Tribological Behaviour of Low-Alloyed Steel Modified by High-Energy Plasma Pulse [Текст] = Особливості мікроструктури та трибологічні властивості низьколегованої сталі, модифікованої високоенергетичним плазмовим імпульсом / Yu.G. Chabak // Журнал нано- та електронної фізики. - 2019. - Т. 11, № 4. - 04010. - DOI: 10.21272/jnep.11(4).04010.
Abstract Метою даної роботи є дослідження мікроструктури і трибологічних властивостей модифікованих шарів, отриманих на поверхні низьколегованої конструкційної сталі 75Г застосуванням високоенергетичного плазмового імпульсу. Модифіковані шари формували за допомогою електротермічного аксіального плазмового прискорювача з напругою розряду до 4 кВ та струмом розряду до 4 кА за поверхневої щільності потужності імпульсу в межах (1.4-1.75)·109 Вт/м2. Мікроструктуру і властивості шарів досліджували з використанням електронної скануючої мікроскопії, рентгеноструктурного аналізу, вимірюванням мікротвердості, а також проведенням випробувань на зношування за схемою "Ball-on-Disk". Результати показали, що однократний плазмовий імпульс з щільністю потужності 1.4∙109 Вт/м2 утворює на поверхні сталі модифікований шар товщиною 13-15 мкм зі структурою наддрібнозернистого мартенситу (15.9 % залишкового аустеніту) із середньою мікротвердістю 985 HV. Підвищення щільності потужності до 1.75∙109 Вт/м2 привело до формування більш товстого модифікованого шару (22-26 мкм), який складається з двох мартенситно-аустенітних субшарів, розділених тонким (0.3-0.5 мкм) аустенітним шаром. Середня твердість внутрішнього та зовнішнього субшарів становить 963 HV та 670 HV відповідно. Зовнішній субшар вміщує підвищену кількість залишкового аустеніту (32 %). Встановлено, що плазмова обробка призводить до насичення модифікованого шару вуглецем (максимально до 1.4 %), який переноситься плазмовим струменем. Плазмова модифікація підвищує трибологічні властивості сталі 75Г, що проявляється у збільшенні зносостійкості на 18-90 % та стабілізації коефіцієнту тертя впродовж випробувань. Процес зношування модифікованих поверхонь відбувається за абразивним механізмом за відсутності інтенсивного окислення поверхні. Знос поверхні полягає у багатоцикловому деформуванні елементів рельєфу із видаленням перенакльопаних мікрочасток металу.
The purpose of the work is to study the microstructure and tribological properties of modified layers obtained on the surface of low-alloyed structural steel 75Mn by the use of high-energy plasma pulse. Subsurface layers were modified using an electrothermal axial plasma accelerator with arc discharge voltage up to 4 kV and discharge current up to 4 kA producing the plasma flux with the power density in the range of (1.4-1.75)∙109 W/m2. The microstructure and properties of the layers were investigated using scanning electron microscopy, XRD, microhardness measurement, and "Ball-on-Disk" wear test. The results showed that a single plasma impulse with power density of 1.4∙109 W/m2 forms on the surface a modified layer of 13-15 µm thick with average microhardness of 985 HV consisting of ultrafine-grained martensite and 15.9 vol. % of retained austenite. Increasing power density to 1.75∙109 W/m2 led to the formation of modified layer of bigger width (22-26 µm) comprising two martensite-austenite sublayers divided by thin (0.3- 0.5 µm) austenitic layer. The average microhardness of inner and outer sublayers is 963 HV and 670 HV respectively. The outer sublayer contains higher volume fraction of retained austenite (32 vol. %). It was found that plasma treatment leads to enrichment of the modified layer with plasma-transferred carbon which up to 1.4 wt. %. Plasma modification improves the tribological properties of 75Mn steel, that manifests in increasing wear resistance by 18-90 % and stabilizing the coefficient of friction during the wear testing. The wear process of modified surfaces takes place according to abrasive mechanism with groove formation without intense surface oxidation. The surface deterioration occurs due to multiple deformation of relief elements with detachment of highly deformed microchips.
Appears in Collections: Журнал нано- та електронної фізики (Journal of nano- and electronic physics)

Views

China China
1
Germany Germany
8724
Greece Greece
1292
Ireland Ireland
46046
Lithuania Lithuania
1
Netherlands Netherlands
322
Sweden Sweden
1
Ukraine Ukraine
692843
United Kingdom United Kingdom
346745
United States United States
2032474
Unknown Country Unknown Country
692842
Vietnam Vietnam
1294

Downloads

Ireland Ireland
1
Lithuania Lithuania
1
Slovakia Slovakia
1
Ukraine Ukraine
2032474
United Kingdom United Kingdom
1
United States United States
692841
Unknown Country Unknown Country
6
Vietnam Vietnam
1

Files

File Size Format Downloads
Chabak_jnep_4_2019.pdf 693,73 kB Adobe PDF 2725326

Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.